Kit Avançado p/ Arduino (com placa UNO R3) - Keyestudio KS0075

:ARD04034
51,95 €
preço com IVA incluído

Este Kit avançado para Aduino ajuda-te a saber usar um Arduino de maneira prática. O kit já inclui o Arduino UNO R3 e uma seleção de componentes eletronicos mais comuns, como LEDs, resistências, sensores, etc. e vem acompanhado com um manual de 21 projetos, começando pelo básico da eletrônica até projetos mais complexos.

Se quiseres saber mais sobre este Kit, consulta a sua Wiki Page

Quantidade

DESCRIÇÃO EM PORTUGUÊS BREVEMENTE DISPONÍVEL

Se tiver alguma dúvida neste produto não hesite em contactar-nos.

*Atenção: as imagens são meramente ilustrativas.

Overview:

 

 

Keyestudio REV4 is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

The REV4 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 programmed as a USB-to-serial converter.

 

format,webpformat,webpformat,webp

 

Components List

5x LED - Blue    
5x LED - Red    
5x LED - Yellow        
1x LED - RGB        
8x 220 Ω resistor        
5x 10K Ω resistor        
5x 1K Ω resistor            
1x 10K Ω Pot        
1x Buzzer (active)    
1x Buzzer (passive)    
4x Large button switch    
2x Ball tilt sensor    
3x Photo Resistor        
1x Flame sensor        
1x LM35 Temp Sensor    
1x IC 74HC595N 16-pin DIP
1x 7-seg LED 1x module    
1x 7-seg LED 4x module    
1x 8*8 LED Matrix        
1x 2x16 LCD display        
1x IR receiver            
1x IR remote control        
1x Servo Motor            
1x Stepper driver module    
1x Stepper Motor        
1x Joystick module        
1x Relay module

1x PIR Motion Sensor                    
1x Analog Gas Sensor                    
1x ADXL345 Three Axis Acceleration Module    
1x HC-SR04 Ultrasonic Sensor    
40x Pin headers                    
1x 830 hole Breadboard                
10x Dupont connector wires                
30x Jumper Wire                    
1x 6-cell AA Battery pack            
1x USB cable                        
1x Resistance color ring meter
1x Arduino UNO R3

 

Features:

1. Microcontroller core: AVRmega328P-PU ( Processing speed 20MIPS)

2. Working voltage: +5V

3. External input voltage:+7V~+12V(suggest)

4. External input voltage ( extremum ): +6V≤ Vin ≤ +20V

5. Digital signal I/O interface: 14 ( 6 PWM input interface)

6. Analog signal input interface: 6

7. DC I/O interface current: 40mA

8. Flash capacity: 32KB( other 2k used in hootloader)

9. SRAM static storage capacity

10. EEPROM storage capacity: 512bytes

11. Clock frequency:16MHZ

 

Documents:

Wiki Page Tutorial

Tutorials

ARD04034_projects.pdf

ARD04034

Também poderá gostar