EMW3162 WIFI Shield for Arduino/Nucleo
  •  EMW3162 WIFI Shield for Arduino/Nucleo
  •  EMW3162 WIFI Shield for Arduino/Nucleo
  •  EMW3162 WIFI Shield for Arduino/Nucleo
  •  EMW3162 WIFI Shield for Arduino/Nucleo
  •  EMW3162 WIFI Shield for Arduino/Nucleo
  •  EMW3162 WIFI Shield for Arduino/Nucleo

EMW3162 WIFI Shield for Arduino/Nucleo

:ARD03105
€16.18
Tax included

DISCONTINUED

EMW3162 WIFI Shield consists of a base board and a WiFi module EMW3162. It allows you to connect your Arduino/Nucleo board with the Internet. Thanks to the EMW3162 WIFI Shield, WiFi communication will become easy for devices that feature Arduino connectivity.

Quantity
Out-of-Stock


If you have any questions on this product please feel free to contact us.

*Disclaimer: The images are merely illustrative.

Features

 

The WiFi module EMW3162 :

 

  • As easy to use as an serial module with the provided serial transparent transmission firmware
  • High stability, hardly goes down
  • Ultra low power consumption, online standby 7mA only

 

 

The base board :

 

  • Compatible with Arduino interface, use UART only
  • Works as an Arduino WiFi Shield, connects to Arduino boards like : UNO, Leonardo, Nucleo, Xnucleo, etc.
  • Works as an Arduino WiFi board, allows connecting with Arduino shields
  • Onboard USB to UART converter FT230XS, for UART debugging and/or firmware updating
  • Onboard WiFi TX/RX LEDs, indicating the WiFi communication status
  • Supports EasyLink fast matching (instant networking by pushing the SSID and password of the wireless router via smart phone APP)
  • Supports one-key recovery to factory setting (no need to flash the firmware for configuration errors)
  • Flexible boot mode configuration
  • 500mA fast self-recovery fuse, stable and safe

 

 

What's on Board

RPi expansion board on board resource

  1. Arduino interface : for connecting with Arduino boards and/or Arduino shields
  2. EMW3162 connector : for connecting the WiFi module EMW3162
  3. EMW3162 extend pin headers : access to the common used pins of EMW3162
  4. SWD interface : for programming and debugging
  5. USB TO UART interface : for UART debugging and/or firmware updating
  6. FT230XS : onboard USB to UART converter
  7. RT9193-33 : onboard 3.3V regulator
  8. Fuse : 500mA fast self-recovery fuse
  9. BOOT switch
    • turn to H, the BOOT pin will be connected to 3.3V
    • turn to L, the BOOT pin will be connected to GND
  10. STATUS switch
    • turn to H, the STATUS pin will be connected to 3.3V
    • turn to L, the STATUS pin will be connected to GND
  11. WiFi indicator : LEDs for indicating the WiFi communication status
  12. WPS key
    • press the key, the EMW3162 will start WPS matching
    • press the key and hold it for 5 seconds, the EMW3162 will recover to factory setting
  13. EASYLINK key
    • press the key, the EMW3162 will start EasyLink matching
  14. RESET key
  15. Power indicator
  16. WiFi serial port configuration jumpers
    • connect the WFRX to FTTX, WFTX to FTRX respectively, you can communicate with the EMW3162 through USB TO UART interface
    • connect the WFRX to TX, WFTX to RX respectively, you can communicate with the EMW3162 through Arduino interface

 

Development Resources

 

Wiki : www.waveshare.com/wiki/EMW3162_WIFI_Shield

 

ARD03105

You might also like